Digi CM Guia do Utilizador descarregar pdf (Página 20)

Automatic Device Recognition

20 Chapter 1

Port 3 shows a real world example of a detected device.

Automatic Device Recognition also monitors each of the configured serial

ports. This allows you to receive an e-mail or SNMP trap if there is a change in

the expected response from the device connected to the serial port. If the

device goes down or is disconnected for any reason, you are notified.

For configuration of this alarm feature please refer to chapter 4, Configuring

Ports.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 157 158

Digi CM 1
Contents 5
6 Contents 6
8 Contents 8
Introduction 9
Feature Summary 10
Chapter 1 10
Web Interface 11
Configuration Menu 12
14 Chapter 1 14
Port Escape Menu 18
CISCO.Router.port3 19
Sun.nemo.port5 19
20 Chapter 1 20
Getting Started 21
22 Chapter 2 22
The Digi CM 23
Configuring a Port for SSH 24
Procedure 25
About Shell Options 26
Digi CM 32 show 27
Chapter 3 31 31
Adding a Serial Modem 32
Chapter 3 32
System and Port Logging 33
Enable SYSLOG Server 34
Enable A Compact-flash Card 35
Enable Digi CM Memory 36
Viewing System Logs 37
Chapter 5 39 39
5. Click Save & apply 39
Viewing Port Logs 40
Configuring Ports 41
42 Chapter 4 42
Serial port parameters 42
Console Server Mode 44
Terminal Server Mode 45
Dial-In Modem Mode 46
Dial-In Terminal Server 46
SSH, Raw TCP, and 48
DTR Behavior 49
Inter-character Timeout 49
Serial Port Parameters 50
Chapter 4 50
Alerts and Notifications 51
56 Chapter 5 56
Port logging 56
Port event handling 56
User Administration 59
Administering Users 60
Chapter 6 60
4. Click Apply changes 60
192.168.1.108 61
Filter IP: 192.168.1.0 61
Filter Mask: 255.255.255.0 61
192.168.5.10 61
Chain rule 63
64 Chapter 7 64
Chapter 7 65 65
• or restrict rights to Jeff 65
Sniff Session 66
Permit monitor only mode 67
Authentication 67
68 Chapter 7 68
Custom and Default Menus 69
Creating Menu Names 70
Adding Menu Items 71
Assigning Users to a Menu 72
Default Menu 74
Chapter 8 74
Microsoft SAC Support 75
Command Syntax 76
Command Example 76
78 Chapter 9 78
Chapter 9 79 79
Field Description 79
Chapter 9 80
Host mode configuration 81
82 Chapter 10 82
Assign a port name: 82
Chapter 10 83 83
Chapter 10 84
86 Chapter 11 86
88 Chapter 11 88
Chapter 11 90
Add the power controller 93
98 Chapter 12 98
100 Chapter 12 100
Power Controller 101
Chapter 12 101 101
Chapter 12 102
Port Clustering 103
104 Chapter 13 104
Chapter 13 105 105
106 Chapter 13 106
Configuring Port Clustering 108
Chapter 13 108
10.Click Save & apply 108
Clustering Parameters 109
Accessing the Cluster Ports 109
110 Chapter 13 110
System Administration 111
112 Chapter 14 112
114 Chapter 14 114
116 Chapter 14 116
Command Line Interface 117
Chapter 15 119 119
File Name Description 120
122 Chapter 15 122
124 Chapter 16 124
126 Chapter 16 126
Configure System Logging 127
128 Chapter 16 128
130 Chapter 16 130
Viewing A Sniff Session 131
132 Chapter 16 132
134 Chapter 16 134
136 Chapter 16 136
124 for more information 137
Hardware Test Menu 138
Disaster Recovery 138
Use the ESC key 139
Chapter 16 140
Hardware Information 141
Hardware Specifications 142
Chapter 17 142
Attribute Value 142
DB-25 Male Console Adapter 144
Chapter 17 145 145
RJ-45 Signal DB-9F Signal 145
Cable Adapters 146
RJ-45 Signal DB-25M Signal 146
Chapter 17 147 147
(Available but not included) 148
Rack shown in illustration is 149
150 Chapter 17 150
Certifications 151
Safety Instructions 152
Solaris Ready 154
Chapter 18 154
Index 155 155
156 Index 156
157 Index 157
90000301 158

Comentários a estes Manuais

Sem comentários

Digi CM Guia do Utilizador Página 20

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Digi CM